Mts SWIFT 50 GLP Sensor Heavy Trucks Manual de usuario descargar pdf (Pagina 90)

DESCRIPTION

INFORMATION AND DESIGN(S)

DISCLOSED HEREIN ARE CONFIDENTIAL

AND THE PROPERTY OF MTS SYSTEMS

CORPORATION AND MAY NOT BE USED,

REPRODUCED OR DISCLOSED IN ANY

FORM EXCEPT AS GRANTED IN WRITING

BY MTS SYSTEMS CORPORATION. THIS

RESTRICTION EXCLUDES INFORMATION

THAT IS IN THE PUBLIC DOMAIN OR

WAS LEGITIMATELY IN THE PRIOR

POSSESSION OF THE RECIPIENT.

PROPRIETARY DATA

SOURCE/REF

DRAW

ING

MATERIAL DESCRIPTION

MATERIAL SIZE

FINISH

MASK

THREAD DEPTHS ARE TO MIN FULL TH DS

DRILL DEPTHS ARE TO FULL DIA

REMOVE BURRS AND SHARP EDGES

DO NOT SCALE PRINT

SCALE

MACHINED

SURFACES

180

UNLESS OTHERWISE SPECIFIED

.XXX HOLE SIZE TOLERANCE

0.000

TO .750

+.010/-.002

OVER .750

TO 1.500

+.015/-.003

2ANGLE

GENERAL

TOLERANCES

.XX

.XXX

THIRD

ANGLE

PROJ

MTS SYSTEMS CORPORATION

1/4

EDE

N PRAIRIE, MINNESOTA U.S.A.

.03

.010

DRAWN

CHE

ENGR

DATE

MFG

DATE

DATEDATE

SIZE

TITLE

NEXT LEVEL

PRODUCT CODE

NUMBER

SHEET OF

REV

REVISIONS

DATE

ENGR

RAWN

LETTER

ECN NO

ATTACH COVER (ITEM 4) TO BOX. APPLY RTV TO GROOVE AND CONNECTOR AS SHOWN.

APPLY LOCTITE 222 AND TORQUE TO 7 IN-LBS.

APPLY LOCTITE 222 AND TORQUE TO 9 IN-LBS.

BACKSHELL, AROUND (4) COVER SCREW HOLES AND TOP GROOVES OF CABLE ACCESS SLOT.

NOTES:

1) ATTACH PWB (ITEM 2) TO CONNECTOR (ITEM 3). SOLDER PCB PIN CONNECTIONS AND

CABLE CONNECTIONS PER SHEET 2 WIRING SCHEMATIC.

2) APPLY K250 HIGH TEMPERATURE TAPE TO PWB. PLACE ONE BAND (1 INCH WIDE) OVER

CONNECTOR SOLDER CONNECTIONS AND ANOTHER OVER CABLE SOLDER CONNECTIONS.

3) ASSEMBLE PWB & CONNECTOR TO BOX (ITEM 1). PRIOR TO, APPLY RTV TO CONNECTOR,

FILL BOARD MOUNTING HOLES AND APPLY LAYER OF RTV IN CABLE ACCESS SLOT ON BOX

AS SHOWN. REMOVE ANY EXCESS RTV AFTER INSTALLING.

4) APPLY RTV ALL AROUND OUTSIDE EDGE OF BOARD,OUTSIDE EDGE OF THE CONNECTOR

RLJ

BAO

3-31-09 -

4-09 -

-----

1/1

574462-XX

FROM: 6, TO: 4.

BOX, MDM, SWIFT 50GLP

6-12-12

RLJRLJ

CABLE ASSY-MODULE

-05 & -06 TO REV B.

UPDATE DOCUMENT REV.

CHANGE ITEM 5 QTY

500001048

RTV INSIDE GROOVE

RTV AROUND (4) COVER SCREWS HOLES

APPLY RTV TO AREA

(TH

IS SIDE & OPP. SIDE)

APPLY RTV TO GROOVE AND TOP OF CONNECTOR

1 25

11 14

9 10

(

INSTALL FROM THIS SIDE)

LENGTH

(SEE TAB ON SHT 2)

FLANGE BEFORE INSTALLING

TO PROVIDE PROPER SEALING

APP

LY RTV TO BOTH SIDES

AND BOTTOM OF CONNECTOR

NOTE THE ORIENTATION

OF CONNECTOR DOVETAIL

SEAL WITH RTV (4 PLACES)

RTV AROUND CABLE EXIT

SECTION A-A

RTV

GROOVES

1 2 ... 85 86 87 88 89 90 91 92 93 94 95 ... 111 112

Comentarios a estos manuales

Sin comentarios

Mts SWIFT 50 GLP Sensor Heavy Trucks Manual de usuario Pagina 90

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Mts SWIFT 50 GLP Sensor Heavy Trucks