Mts SWIFT 40 Sensor Manual de usuario Pagina 42
- Pagina / 170
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SWIFT 40 Sensors
42
Transducer Interface
Hardware Overview
TI Jumpers
The transducer interface uses circuit board jumpers to establish certain
parameters and make use of various electronic functions. These jumpers are set at
the factory, and should not be reset. The following table is for reference only.
TI PWB Jumper Locations
J
UMPER SETTING FUNCTION
X1
1–2
2–3
Excitation setup for shunts FX1, FY1, FY4, and FZ2.
Sets up – (minus) excitation for shunts FX1, FY1, FY4, and FZ2.
Sets up + (plus) excitation for shunts FX1, FY1, FY4, and FZ2.
X2
1–2
2–3
Excitation setup for shunts FX2, FY2, FY43 and FZ1.
Sets up – (minus) excitation for shunts FX2, FY2, FY43 and FZ1.
Sets up + (plus) excitation for shunts FX2, FY2, FY43 and FZ1.
X4 removed
Not used for TI applications (Standard setting).
X5 installed
removed
Enables the ability to download new code to the block of FLASH RAM
where the boot code is stored.
Disables the ability to download new code to the block of FLASH RAM
where the boot code is stored (Standard setting).
X6 installed
removed
Boots to the FLASH memory down-loader.
Boots to the Transducer Interface software (Standard setting).
X2
X1
X4
X5
X6
S20-13
- SWIFT® 40 Sensor 1
- Product Information 1
- Publication information 2
- Contents 3
- Analyzing SWIFT Data 105 4
- Maintenance 117 5
- Troubleshooting 121 5
- Assembly Drawings 135 5
- If You Contact MTS by Phone 9
- SWIFT 40 Sensors 10
- Technical Support 10
- Before You Begin 11
- Conventions 12
- SWIFT 40 Sensors Preface 13
- Hardware Overview 15
- Construction 18
- Non-spinning 20
- Additional 21
- Design Features 22
- Coordinate System 23
- Specifications 25
- Transducer Center-of-Gravity 26
- ALUMINUM TITANIUM 26
- ARAMETER SPECIFICATION 27
- ARAMETER SPECIFICATION 28
- Calibration 29
- Checking the 30
- TI Front Panel 34
- AngleFixed=0 35
- LGORITHM 36
- of range) occurred on 39
- AIL INDICATOR STATE 40
- TI Rear Panel 41
- TI Jumpers 42
- Interfacing with RPC 43
- Software Utilities 45
- Introduction 46
- More about TIXFER 49
- Error Status,” on page 58 51
- Error Messages 57
- Shunt Error Status 58
- Select a Zero Method 60
- Calibration File Elements 61
- Zero Algorithms 62
- Upload the Calibration File 64
- Edit the Calibration File 65
- UTPUTS MZ MY MX FZ FY FX 66
- Z MY MX FZ FY FX 66
- Description 67
- Download the Calibration File 69
- Test Track Vehicle 72
- OLT SIZE 77
- ORQUE INCREMENT M8 M10 M14 77
- Considerations for 82
- Choosing a Zero 83
- Axes Icon 85
- Angle Zero 86
- Switch and Indicator 86
- Bridge Zero 86
- SWIFT 40 A (Aluminum) 91
- SWIFT 40T (Titanium) 91
- Effect of Zero 92
- Reference on SWIFT 92
- Collecting Data 94
- Road Simulator 100
- Installing the Transducer 100
- Communication Configurations 102
- Cable Configurations 103
- Termination Jumper 104
- Analyzing SWIFT Data 105
- The Data 106
- Fx Data (Longitudinal Force) 107
- Fx Offset=165N 108
- Fz Data (Vertical Force) 109
- Mx Data (Overturning Moment) 110
- My Data (Brake Moment) 113
- Slalom Curve Driving Example 116
- Maintenance 117
- Transducer 118
- Transducer Interface 119
- Troubleshooting 121
- Signal Outputs appears to 124
- TI electronics have been 124
- One or more 126
- Troubleshooting Guide 127
- Assembly Drawings 135
- Cable Drawings 136
- SWIFT 40A Mechanical Drawings 151
- SWIFT 40T Mechanical Drawings 155
- Common Parts 161
Relacionado con productos y manuales para Hardware Mts SWIFT 40 Sensor
Hardware Mts SWIFT 45 GLP Sensor Manual de usuario
(106 paginas)
(106 paginas)
Hardware Mts SWIFT 50 GLP Sensor Manual de usuario
(70 paginas)
(70 paginas)
Hardware Mts SWIFT 10 ATV Sensor Manual de usuario
(144 paginas)
(144 paginas)
Hardware Mts Series 249 Swivels Manual de usuario
(40 paginas)
(40 paginas)
Hardware Mts SWIFT 10 MC Sensor Manual de usuario
(144 paginas)
(144 paginas)
Hardware Mts Acumen Electrodynamic Manual de usuario
(42 paginas)
(42 paginas)
Hardware Mts Criterion Series 40 Manual de usuario
(48 paginas)
(48 paginas)
Hardware Mts Criterion Series 60 Manual de usuario
(42 paginas)
(42 paginas)
Hardware Mts Criterion Series 40 Manual de usuario
(142 paginas)
(142 paginas)
Hardware Mts Criterion Series 60 Manual de usuario
(146 paginas)
(146 paginas)
Hardware Mts 85X Damper Manual de usuario
(56 paginas)
(56 paginas)
Hardware Mts Landmark Tabletop Manual de usuario
(122 paginas)
(122 paginas)
Hardware Mts Material Test Systems Manual de usuario
(80 paginas)
(80 paginas)
Hardware Mts TestLine Manual de usuario
(132 paginas)
(132 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales